| CRE - Racing Engine Componets and Stroker Short Blocks For Camshafts see the bottom of the page |
| Steel Retainers (sets of 16) B.B. - 11/32" or 3/8" 7 degree - $ 56.00 Titanium Retainers (sets of 16) B.B. - All 10 degree - $ 159.95 Machined Steel Valve Locks (sets of 32) 7 degree B.B. - 11/32" or 3/8" - $ 29.00 B.B. - 10 degree super locks 11/32" or 3/8" 10 degree - $ 29.00 |
| Hydraulic Lifters Stock- for cams less than 230 degress @ .050" Set of (16) - $ 92.00 - All B.B. & S.B. Racing Lifters -For cams over 230 degress @ .050" Set of (16) - $ 105.00 - All B.B. & S. B. These high energy lifters have a light weight check valve disc that allows for quicker response. This results in increases in engine speed before valve float. Solid Lifters - For all solid Lifter Camshafts Set of (16) - $ 125.00 - All B.B. & S.B. |
| Valve Springs - B.B.Single with Damper P/N 9905 $80.00 B.B. Double Springs (set of 16) P/N - 929-16 2 spring with damper $ 149.95 1.535" o.d. .755" i.d. 150# @ 1.880" 434# @ 1.230" Good for a .650" lift cam |
| Dampers Stock - (non-SFI) good to 6500 rpm CRE-80012 S.B. 318/340/360 $ - 85.00 CRE - 80013 B.B. 383-440 $ - 85.00 All Steel - SFI approved, black painted, Engraved timing marks, absorbs engine vibrations. Timing marks every 90 degrees CRE - 8006 B.B 383-440 int. Bal $ - 149.95 Fluid Filled - SFI approved, engraved timing marks, improves performance and bearing life. CRE -712420C 318/340/360 Int. Bal. 71/4" dia. $ -179.95 CRE - 712425C 383-440 Int. Bal. 71/4" dia. $ -179.95 Cyco - steel dampers $ 299.95 All three series are very nice pieces!!! |
| ARP - Head Bolts B.B. Main Bolts ARP.140-5001 - $ 32.95 B.B. Hemi (4) Bolt ARP.145-5201 - $ 64.95 B.B. Head Studs ARP.145-4006 - $149.95 B.B. Main Studs ARP.140-5401 - $ 65.95 B.B. Head Bolts (Edelbrock) ARP.145-3606 - $ 69.95 Damper Bolts ARP.245-2501 - $ 29.95 FEL-Pro valve cover gaskets - Click here FEL-Pro Pan gaskets - Click here FEL-Pro Head Gaskets Click here S.B. - 1008 - $88.00 pair B.B. - 1009 - $88.00 pair HIgh volume Oil Pumps by Clevite 77 S.B. - $ 59.00 B.B. - $ 69.00 |
| CNC Machined Blocks - Available Now 400 /440 - Base Block with the following options: 340/360 - Small Blocks - Baked Clean and vibrated - All holes retapped - UltraSonic checked for Wall thickness - Decked to clean up or your Spec. - ARP Main Studs installed - Line bored to within.0002" w/stock caps - CNC notched for a stroker crankshaft - Lifter Bores CNC corrected w/lifter sleeves - Bored to within .004" of overbore for honing - Jet Cleaned and Bagged - Assembly ready $1950.00 plus shipping ( Honing and other options available) ( send us your core for a $300 savings) |
| Call for ordering a "Custom" ground camshaft for your special project. We believe that each engine package needs the cam custom taylored to match the balance of the Engine and drive train components. See the cam page for details. |
 |
 |
 |
 |
| Pushrods S.B. - Stock S.B. - Custom Cut to Lenght $175.00 All pushrods Chrome Moly material B.B. - Stock Set of (16) $ 29.95 B.B. - Custom Cut to Lenght $175.00 (400-500) lbs B.B. - Custom cut to length $199.00 (heat treated chrome moly) (500 - 600) lbs |
 |
| 4.500" 4340 Billet Stroker Cranks Special cleanance on these cranks 4.500" Ground with 440 mains, and 440 pins. $795.00 4.500" Ground with 440 mains, and 2.200" chevy pins. $795.00 4.500" Ground with 400 mains, and 2.200" chevy pins. $795.00 Turn Counter Weights for 400 Block $ 175.00 Chamfered bearings for all above Mains and Rods $ 200.00 Balancing availabe on Crank Kits |
 |
 |
 |
 |
 |
 |
 |